Ms. Jenny Wang

What can I do for you?

Ms. Jenny Wang

What can I do for you?

Home> Industry Information> How to design plastic injection mold gate?

How to design plastic injection mold gate?

April 04, 2019

Injection machine gate design is related to the size of the plastic sample parts structure and mold shape as well, as well as the molding process parameters and performance of the plastic part. However, as long as basic function is considered, gate cross section is small and the length is short, in this way it can meet the requirements of increasing the flow rate, rapid cooling and closing, and the separation of the plastic parts and the minimum gate residue are satisfied.
1. The gate location needs
Satisfied requirement
Appearance requirements (gate marks, weld lines)
Product function requirements
Mold processing requirements
Warpage of the product
The gate is not easy to remove
Molding process is easy to control
2. Impact on production and function
The flow length determines the injection pressure, the clamping force, and the shortened full flow length of the product can reduce the injection pressure and clamping force.
The position of the gate will affect the holding pressure, the pressure of the holding pressure, and whether the holding pressure is balanced. Keep the gate away from the position of the product (such as the bearing) to avoid residual stress. The gate position must consider the exhaust to avoid the accumulation of wind. Occur, do not place the gate in a weaker place or in the embedding to avoid misalignment.
3. Tips for choosing a gate location
Gate
The gate is a short groove with a small cross-sectional area for connecting the flow path to the cavity. The cross-sectional area is so small that the purpose is to achieve the following effects:
Not long after the cavity is filled, the gate is cold
Simple water removal
The water removal is completed, leaving only a few traces
Make the filling of multiple cavities easier to control
Reduce excess filler
Gate location and size
1 Place the gate at the thickest part of the product and pour it from the thickest part to provide better filling and holding pressure. If the holding pressure is insufficient, the thinner area will solidify faster than the thicker area, avoiding the gate being placed at a sudden change in thickness to avoid hysteresis or short shots.
2 If possible, pouring from the center of the product, placing the gate in the center of the product can provide the same length of flow, the length of the flow will affect the required injection pressure, and the central pouring will make the pressure in all directions uniform. Avoid uneven volume shrinkage.
3 When the plastic flows into the flow path, the plastic first heats down (cools) and solidifies near the die face. When the plastic flows forward, it flows only through the solidified plastic layer. Moreover, since the plastic is a low heat transfer material, the solid plastic forms a green layer and the retaining layer can still flow.
Therefore, in the ideal case, the gate should be placed in the cross-flow layer position to make the best plastic flow effect. This situation is most common in circular and hexagonal cross-flow paths. However, trapezoidal cross-flow paths do not achieve this effect because the gate cannot be placed in the middle of the flow path.
When determining the location of the gate, the following principles should be followed:
The rubber injected into each part of the cavity should be as even as possible;
The rubber compound injected into the mold shall maintain a uniform and stable flow front at all stages of the injection process;
Consideration should be given to possible occurrence of weld marks, air bubbles, pockets, imaginary position, insufficient shot glue and glue spray;
The water removal operation should be as easy as possible, preferably automatic operation;
The location of the gate should be compatible with all aspects.
There are no hard and fast rules for designing gates. Most of them are based on experience, but there are two basic elements that need to be compromised:
The larger the cross-sectional area of the gate, the better, and the shorter the length of the channel, the better, to reduce the pressure loss when the plastic passes.
The gate must be narrow so that it can be easily cold-knotted and prevent excessive plastic from flowing backwards. Therefore, the gate should be in the center of the flow channel, and its cross-section should be as circular as possible. However, the gate switch is usually determined by the switch of the module.
Gate size
The size of the gate can be determined by the cross-sectional area and the length of the gate. The following factors determine the optimal size of the gate:
Rubber flow characteristics
Thickness of the module
The amount of rubber injected into the cavity
Melting temperature
Tool temperature
4. Balance of the gate
If a balanced runner system is not available, the following gate balancing method can be used to achieve the goal of uniform injection molding. This method is suitable for molds with a large number of cavities.
There are two ways to balance the gate: changing the length of the gate channel and changing the cross-sectional area of the gate. In another case, when the cavity has a different projected area, the gate also needs to be balanced.
At this time, to determine the size of the gate, it is necessary to first determine the size of one of the gates, find the ratio of its gate cavity volume, and apply this ratio to its gate and each corresponding cavity. In comparison, the size of each gate can be determined successively. After the actual test, the balance operation of the gate can be completed.
5. Direct gate or large nozzle
The sprue supplies the plastic directly to the finished product, and the sprue adheres to the finished product. In the two-plate mold, the big nozzle is usually one out, but in the design of the three-plate mold or the hot runner mold, it can be more than one beer.
Disadvantages: The formation of a stencil on the surface of the finished product will affect the appearance of the finished product, while the size of the stencil is in the fine diameter hole of the nozzle.
6. The draft angle of the nozzle, the length of the nozzle
Therefore, the large water jet printing can be reduced, as long as the size of the above-mentioned nozzle is changed to be small. However, the diameter of the nozzle is affected by the diameter of the nozzle, and the nozzle is easy to be out of the mold, and the draft angle cannot be less than 3 degrees, so only The length of the nozzle can be shortened, and the length can be shortened.
Gate selection:
The gate is the connecting part of the flow channel and the cavity, and is also the last part of the injection mold feeding system. Its basic function is:
The molten plastic from the flow path enters the filled cavity at the fastest speed.
After the cavity is filled, the gate can be quickly cooled and closed to prevent the cavity from flowing back to the uncooled plastic.
PS: (The Tsui Tsui is a very important part of the mold. The heated and dissolved plastic is injected into the mold through the nozzle to form the product, which is assembled in the middle of the front mold (A board).
7. Summary
The design of the gate is related to the size of the plastic part, the shape of the mold, the injection process conditions and the performance of the plastic part. However, as far as the basic function is concerned, the cross section of the gate is small and the length is short, because only in this way can the requirements of increasing the flow rate, rapid cooling and closing, and the separation of the plastic parts and the minimum gate residue are satisfied.
The main points of the gate design can be summarized as follows:
1) The gate is opened in the thick section of the plastic part, so that the molten material flows into the thin section from the thick material section to ensure the filling is complete;
2) The choice of gate location should minimize the plastic filling process to reduce pressure loss;
3) The choice of gate location should be beneficial to eliminate air in the cavity;
4) The gate should not be allowed to flush the melt directly into the cavity, otherwise it will generate a swirling flow, leaving traces of the rotation on the plastic part, especially the narrow gate is more prone to such defects;
5) The choice of gate location should prevent the formation of seam lines on the plastic surface. Especially in circular or cylindrical plastic parts, the cold well should be added at the melt casting of the surface of the gate. ;
6) The gate position of the injection mold with the elongated core should be far from the forming core, so that the forming core is not deformed by the flow;
7) When forming large or flat plastic parts, a double gate can be used to prevent warpage, deformation and lack of material;
8) The gate should be opened as far as possible without affecting the appearance of the plastic part, such as the bottom of the edge;
9) The size of the gate depends on the size, shape and plastic properties of the plastic part;
10) When designing multiple cavity injection molds, consider the balance of the flow channels to consider the balance of the gates, and try to make the molten materials uniformly charge at the same time.

The above is the How to design plastic injection mold gate? we have listed for you. You can submit the following form to obtain more industry information we provide for you.

You can visit our website or contact us, and we will provide the latest consultation and solutions

Share to:

Send Inquiry

Home> Industry Information> How to design plastic injection mold gate?

Copyright © 2024 Zhejiang Ceeto Mold Co.,Ltd. All rights reserved. Privacy Policy

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send